CONSTRUCTION AND FABRICATION OF AN ICE-BLOCK MAKING MACHINE

Related Articles

DESIGN AND INSTALLATION OF 200 WATT SOLAR POWER SYSTEM

DESIGN AND CONSTRUCTION OF A MEDICAL ALARM

DESIGN AND CONSTRUCTION OF A PROGRAMMABLE THERMOSTAT

CONSTRUCTION AND FABRICATION OF AN ICE-BLOCK MAKING MACHINE

• Format: Ms Word Document
• Pages: 73
• Price: N 3,000
• Chapters: 1-5
• Download Full and Complete Project

Abstract

This work is titled construction and fabrication of an ice block making machine. Ice block making machine revolves around the concept of refrigeration. The concept of refrigeration revolves around the reverse Carnot cycle. This is a cycle involving isentropic expansion (at the throttling valve), isothermal expansion (at the evaporator), isentropic compression (at the compressor) and isothermal compressor ( at the condenser) Compression raises the temperatures of the refrigerant above that of its natural surrounding so that it can give up its heat in a heat exchanger to a heat sink such as air or water (condenser). Expansion lowers the refrigerant temperature below the temperature that is to be produced inside the cooling compartment.

 

TABLE OF CONTENT

Title page
Approval page
Dedication
Acknowledgment
Abstract
Chapter one: Introduction
Chapter Two: Literature Review
Chapter Three:     Design Analysis and Calculations

1. 1. Determination and choice of condenser and Evaporator temperature.
   2. Cooling Load Calculation
   3. Flow Rate
      1. Mass flow rate
      2.  Ton of Refrigeration
      3. Volume flow rate
   4. Determination of Compressor size
   5. Determination of pipe size and length
      1. Comparing the velocities for different pipe size.
      2. Summary table.

Chapter Four: Construction Details

1. 1. Material Selection
   2. Sequence of operation
   3. Assembly

Chapter Five: Cost Analysis
Chapter Six: Recommendation

1. 1. Maintenance and use Instructions
      1. Condenser Maintenance
      2. Defrosting
      3. Other Instructions
      4.  Common Complaints, Causes and Remedy

Chapter  Seven: Refrigerants

1. 1. Requirements for refrigerants
   2. Identifying Refrigerants by number
   3. Halide refrigerants
   4. Grouping and Classification of refrigerants
   5. Group one Refrigerants
   6. R-12 Dichlorodi Fluoromethane (ccl2f2)
   7. R-22 Monochlorodi fluoromethane (CHCLF2)
   8. R-11 Trichloromono fluoromethane (CCL3F)
   9. Azeotropic Mixtures
   10. R-500 Refrigerant
   11. R-502 Refrigerant (R-22 + R-115) (CHCLF2/CCLF2 CF3)
   12. R-503 Refrigerant (R-23 +R-13) (CHF3/CCLF3).
   13. R-504 Refrigerant (R-32 +R115) (CH2F2 (F3 CCLF2)
   14. Group  two refrigerants
   15. R- 717 Ammonia (NH3)
   16. Group three refrigerants
   17. Expendable Refrigerants
   18. Water  as a Refrigerants
   19. Refrigerant Cylinders
   20. Color code for refrigerants cylinders

Chapter Eight: Conclusion
Reference.

 

CHAPTER ONE

1.1                                       INTRODUCTION

This project is on construction and fabricate an ice block making machine. Ice making machine may refer to either a consumer device for making ice, found inside a home freezer; a stand-alone appliance for making ice, or an industrial machine for making ice on a large scale. The term “ice machine” usually refers to the stand-alone appliance.
The ice generator is the part of the ice machine that actually produces the ice. This would include the evaporator and any associated drives/controls/subframe that are directly involved with making and ejecting the ice into storage. When most people refer to an ice generator, they mean this ice-making subsystem alone, minus refrigeration.
An ice machine, however, particularly if described as ‘packaged’, would typically be a complete machine including refrigeration and controls, requiring only connection to utilities.
The second chapter of these write-up  ushers in a precise review of the history and literature of  refrigeration from ancient man to modern day or contemporary  man (i.e modern refrigerating equipment).
Chapter three deals in detail on the methods of calculating refrigeration equipment. Chapter four sequentially gives the overview of the factors, qualities and properties considered in choice decision of the material components (both standard/ranging engineering materials) used for the fabrication and the steps undergone in the assembly of the components to form the refrigerating equipment.
The fifth chapter analysis the material and labour cost incurred in the course of undertaking this project. Chapter six, ummarily is a low down of the maintenance and use instructions to be strictly adhered to in order to make the most effective, economic and efficient use of the refrigerating equipment as well as enable the equipment complete its service life. There is also a provision in this part for the notification of the usual defects observed or experienced during use and the corresponding panacea for them. Included is the reference for future consultancy which helps the student or reader who decides to embark on further research or a fact finding mission on innovations that may add as a filling to this work or to the topic as a whole.
This write-up within its scope is moderate sufficient to the educate the reader on the design and fabrication of ice block making machine.

1.2                          OBJECTIVE OF THE PROJECT
The main objective of this project is to construct and fabricate an ice block making machine, a consumer device for making ice

1.3                       SIGNIFICANCE OF THE PROJECT

Sea water flake ice machine can make ice directly from the sea water. This ice can be used in fast cooling of fish and other sea products. The fishing industry is the largest user of flake ice machines. Flake ice can lower the temperature of cleaning water and sea products; therefore it resists the growth of bacteria and keeps the seafood fresh.
Because of its large contact and less damage with refrigerated materials, it is also applied in vegetable, fruit and meat storing and transporting.
In baking, during the mixing of flour and milk, flake ice can be added to prevent the flour from self-raising.
In most cases of biosynthesis and chemosynthesis, flake ice is used to control the reaction rate and maintain the aliveness. Flake ice is sanitary, clean with rapid temperature reduction effect.
Flake ice is used as the direct source of water in concrete cooling process, more than 80% in weight. Concrete will not crack if has been mixed and poured in constant and low temperature.
In Focusun, flake ice is also used for artificial snowing, so it is widely applied in ski resorts and Entertainment Park.
1.4                                    APPLICATIONS OF THE PROJECT
Ice making machine can be used in the cooling process, such as temperature controlling, fish fresh freezing, and beverage bottle freezing. It can be consumed alone and with food or beverages.

Download Full and Complete Project