Home / MECHANICAL ENGINEERING PROJECT TOPICS AND MATERIALS / DESIGN AND FABRICATION OF A CREEP TESTING EQUIPMENT 

DESIGN AND FABRICATION OF A CREEP TESTING EQUIPMENT 

DESIGN AND FABRICATION OF A CREEP TESTING EQUIPMENT
ABSTRACT            The process involves in the design and fabrication of a creep testing equipment ranges from carrying out the feasibility studying of the project to be designed in terms of functionality.  Since it is used in the testing of failure of material under loading different engineering materials employed in the design and fabrication includes bending moments and deflection of bean etc.

The main purpose of this project is to design mechanical system and electrical system capable of estimating the failure respective of the material under constant loading, which creep is defined as the failure or deformation of material under constant loading occurs.

Creep is defined as time dependent deformation of materials under constant load (plastics).

TABLE OF CONTENTS CHAPTER ONE IntroductionPrimary Creep

Secondary Creep

Tertiary Creep

CHAPTER TWO Literature ReviewJapan Creep Research Association (JCRA)

Denison Mayes Group (DMG)

Applied Test System (ATPS)

CHAPTER THREE Material selectionComponents

Standard Parts

CHAPTER FOURFabrication Parts

Sequence of Operation

CHAPTER FIVE

Design Calculation

Experimental Result

CHAPTER SIX Material Cost                                                  Labour Cost    Recommendation                    Conclusion                                                      ReferencesCHAPTER ONE

INTRODUCTION

Creep is defined as time – dependent deformation of a material under a constant stress or load.  At temperature less than 40 percent of the absolute melting point, the extent of creep if negligible, but at temperatures higher than this is commonly thought of as a high temperature test.

The creep material measuring device is a simple unit designed for demonstrating and investigating the creep characteristics of lead polypropylene specimen at room temperature.  A temperature module is provided to enable the investigation/effects of the temperature as a creep rate.

A failure may also be due to a phenomenon called creep, which is the plastic flow of a material under load at elevated temperatures in addition, the actual shape of a part may be responsible for failure for example stress concentrations due to sudden changes in contour must be taken into account.  This is especially true when dynamic loads with direction reversals exist and the material is not very ductile.

The single specimen creep measuring apparatus/machine is a table top apparatus measuring dimensionally 740 x 470 x 310 mm and approximated weight of 14.5kg.  This simple machine uses specimens of lead and various types of plastics which creep significantly at temperature and under loads.

The design is based on a simple lever principle having a mechanical advantage of 8:1 which provides a steady and uniform tensile load.  The extension of the specimen under load is measured by a dial guage.

It is made up of vertical column which is the main supporting frame, a lever beam, a stop watch, dial guage, a set of weigh hanger, connecting strip, Aluminum block, Ammeter, circuit breaker, volt meter, temperature control, thermocouple, Heating element and a panel made of mild steel shut to house the above mentioned components.  To ensure correct loading of the specimen, the load beam is filted with harden connecting strip which load is applied by means of a set of weight hanger as required.  This apparatus is especially designed for teaching.

Generally for satisfactory use of this equipment, a bunch of approximately 1 x 0.6m is recommended.

A creep curve is a plot of the elongation of a tensile specimen versus time, at a given temperature, under a constant load.  The four stages of creep curve is (1) initial elongation flowing the application at load, (2) transient or primary creep, (3) steady state or secondary creep, and (4) tertiary creep.

Below is the creep curve which shows the four stages.

THE PRIMARY CREEP

Fig 1.1:            This is the stage of the curve over which the creep rate, is de/dt, is continuously decreasing as show in the figure above.  This is of interest to a designer since it forms part of the extension reached in a given time and may affect clearance.

THE SECONDARY CREEP

Fig 1.2:            This section is a period of approximately constant creep rate and is termed secondary creep; the creep rate is at a minimum over this region.

This secondary stage is the region at which creep occurs at more or less “STEADY STATE”.  This is the important part of the curve for most applications.

THE TERTIARY CREEP

Fig 1.3:            This stage represents a continuously increasing creep rate and terminates in fracture of the specimen as shown in the figure above.  This tends to be the final stage of the creep curve when the rate of extension accelerates and finally leads to fracture.

Download Full and Complete Project

 

Sharing is caring!

About Hope Ovat

Check Also

CONSTRUCTION OF A POTABLE ELECTRIC OPERATED WITH RADIO CONTROL (WIRELESS REMOTE) MOTOR VEHICLE FOR LONG DANZA BUS

CONSTRUCTION OF A POTABLE ELECTRIC OPERATED WITH RADIO CONTROL (WIRELESS REMOTE) MOTOR VEHICLE FOR LONG …

AUTOMOBILE MOTOR VEHICLE CONSTRUCTION

AUTOMOBILE MOTOR VEHICLE CONSTRUCTION Format: Ms Word Document Pages: 65 Price: N 3,000 Chapters: 1-5 …

THE CONSTRUCTION AND FABRICATION OF A CANDLE MOLDING MACHINE

THE CONSTRUCTION AND FABRICATION OF A CANDLE MOLDING MACHINE Format: Ms Word Document Pages: 65 …

THE CONSTRUCTION OF SIEVE EQUIPMENT

THE CONSTRUCTION OF SIEVE EQUIPMENT Format: Ms Word Document Pages: 65 Price: N 3,000 Chapters: …

THE CONSTRUCTION AND FABRICATED OF A MOBILE DEEP FREEZER

THE CONSTRUCTION AND FABRICATED OF A MOBILE DEEP FREEZER Format: Ms Word Document Pages: 65 …

NYLON CUTTING AND SEALING MACHINE

NYLON CUTTING AND SEALING MACHINE Format: Ms Word Document Pages: 65 Price: N 3,000 Chapters: …

Leave a Reply